There is the normal installation for OSCam and at the bottom is the guide for OSCam ICAM
Oscam on an Enigma2 receiver such as: VU+, Dreambox, Pingulux, Golden Media Reloaded etc.
Preface:
Of course, paths can vary depending on the images used, but there are images such as OpenATV that no longer offer a special camfeed server, i.e. there is no alternative to downloading the Oscam in the image.
Test Cardsharing 24 hours free of charge
What we need:
- An FTP concept like Filezilla,* WinSCP*.
- The editor Notepad++ ,* is the safest because it writes Linux conform.
- The files attached below are the Softcamfeed exclusively for OpenATV!
Config directories:
I have prominent config directories for different images. As described, this can also vary and sometimes you still have to create the config folder.
VTI - etc/tuxbox/config/
HDMU - usr/keys
OpenATV Image - usr/keys
Newnigma2 - /var/keys/
OozooN - /etc/tuxbox/config/
Example Oscam using a VU+ Zero with VTI Image:
1 Press the blue button
2 Use the arrow buttons to scroll down to Extensions and confirm with OK
3 Press the red button to manage extensions
....Short wait the extension feed is updated and downloaded...
4 Use the arrow buttons to select SoftCams and confirm with OK
5 currently select a current Oscam variation and confirm with OK, a green check mark will be set within your selected Oscam version these days press the yellow button afterwards for Execute confirm again with green for Start
...Wait Oscam will be installed...
When this is finished, simply exit everything with Exit and, most usefully, reboot your packaging first, then go to the computer.
PC:
Start WinSCP now
Computer name: enter the IP of the BOX here
Username: is often root
Password: none is set in the course of VTI so leave it blank within additional images it can be dreambox or HDMU etc. This must of course be looked up on the homepage.
Test Cardsharing 24 hours free of charge
Now you are connected to the package and should normally be connected, if not check the information.
And we continue with the VU+ Zero!!!
Navigate to the current directory: etc/tuxbox
In it you will see with protection some files such as satellites.xml, timezone.xml etc. Do not pay attention to them and of course do not delete them! In this directory you create a folder with the name
config
and give it write permissions with 755, you can do this by pressing the right mouse button on the config folder, then Characteristics should appear and you can set the permissions. Once you have done this, please change to the created config folder. At the latest now it is time to download the attached file for the Oscam here.
oscam.conf - oscam.dvbapi - oscam.server - oscam.user
Actually everything is configured so far that you only have to edit the server file and please do this only with the concept Notepad++ to avoid errors.
All you have to do is add the user name and password of your line and everything else is ready. The port should also match, as it applies to all models. If there are any discrepancies, please correct them of course, but everything should fit.
Now all right, record the file after editing and copy all 4 files into the config folder. Also give the files the rights 755 here if it has not already been done independently, this is the best way to be on the safe side. You have done it, close the FTP interface, go to the receiver and restart it.
Attention in my oscam.server file the PORT 7103 (for all packages) is used which of course your line may adapt to your port!
Test Cardsharing 24 hours free of charge
It continues at the receiver:
Once the restart is done, you will of course have to start the Oscam these days, but this will not be necessary during every restart instead it will be saved permanently.
1 Press the blue button
2 Confirm VTI CAM Center with OK
3 Select OSCAM and start with the green button
...So Oscam is started... and you should have a picture, leave everything with exit and enjoy www2.cardsharing-kaufen.com
Install OSCam ICAM Config / Instructions
We always recommend using the installation tool to install the OSCam ICAM, where everything is done automatically
The tool: https://i.tv-lounge.eu/
And now there are also the instructions.
First of all you have to download the OSCam ICAM e.g. V5 V7 V9 there are a lot of them now, so I would advise you to use the tool.
The OSCam ICAM best installed directly above the receiver, in the best case via the feed.
Setting up the configuration file
Search for the location of the Oscam configuration file. They are normally located in the /etc/tuxbox/config/ folder. In my case, these files are located in the /etc/tuxbox/config/ folder. You will find an approximate configuration in the archive in the previously downloaded configuration folder. For oscam-icam to work, you need to change the following files on the receiver: oscam.conf - Open this file. You must add the following line before the [dvbapi] section. Without it iCam will not work: [Stream-Relay] stream_ecm_delay = 0 stream_relay_ctab = 098D Please do not delete the sections [global] and [dvbapi]! Otherwise you will not be able to watch non-ICAM channels (HD+, ORF etc.). In the configuration folder of the archive downloaded above you will find the files oscam.conf and oscam.user, which are valid for most receivers. You must change the oscam.server file
- oscam.server - open this file and replace it completely with the configuration from your e-mail.
Last but not least you need the ICAM bouquet list, it is not worth uploading it here as it changes from time to time.
The tool can even be used to create auto-updates for the bouquet.
The channel list comes after /etc/enigma2
Hello, I have a VU uno 4k, software VTI, with my other provider I always received a zip file, there was a server and a config file in it. I play with oscam, but I don't understand the c lines, with the conversion from cccam to oscam. do I also get a file from you that runs the same with oscam when I move it into the tuxbox file in my vu box? thanks.
How do you do?
We will provide you with a C-line and, if necessary, suitable settings.
However, I cannot answer why you have two files.
Our solution is that you simply insert the C-line in the Tuxbox (if you wish, our file) or the classic way.
I hope I could help you
MfG
Hello
Can you also use Cccam or just Oscam?
Greetings Frank
Hello!
Both are possible, but we recommend Oscam.
Greetings
Hello
Where can I download the file for the Oscam here
Hi
best from your feed from the receiver